info@kandbscreeding.co.uk

Choosing a screed

Cemfloor screed, Gyvlon, Isocrete K and other screed brands compared

Cemfloor screed is a cement based liquid screed, Gyvlon is a calcium sulphate (anhydrite) flowing screed and Isocrete K-Screed is a semi-dry sand and cement screed with a drying additive. The binder decides most of what matters: minimum depth, drying, laitance, tiling and how soon the heating can go on. This guide sets them side by side from the makers' own data sheets.

Bright smooth liquid screed across a large room

Architects and heating designers often name a screed product rather than a screed type. A drawing might say "Cemfloor Therm, 50mm" or "Gyvlon ECO over UFH", and the builder then has to work out what that means for depth, drying and the flooring that goes on top. The product name tells you the binder, and the binder tells you most of what you need to know.

Short answer: Cemfloor is a cement based liquid screed with no laitance to sand off and a minimum floating depth of 35mm in homes. Gyvlon is a calcium sulphate (anhydrite) flowing screed, also 35mm floating in homes, which needs light sanding, priming and drier moisture limits before tiling. Isocrete K-Screed is a hand laid sand and cement screed with an additive that speeds drying, generally laid 65mm thick floating in homes.

Everything below comes from the manufacturers' own published data sheets and guidance, listed under Sources. We have no supply agreement with any of these brands, and we do not claim approved installer status for any of them. Where a data sheet for your exact product says something different, follow the data sheet.

Cement based liquid screed (Cemfloor) vs calcium sulphate (Gyvlon, alpha flow)

Liquid screeds fall into two families. Your specification shows which one you have: CT in the designation means cement, CA means calcium sulphate, under BS EN 13813.

Cemfloor screed: cement based liquid screed

Cemfloor is made by mixing the Cemfloor binder with cement, sand and water at the batching plant. Its data sheets (Cemfloor Therm and Cemfloor NH, 2024 versions) give these figures:

  • Strength classes: C20, C25 or C30 compressive, F4, F5 or F6 flexural.
  • Minimum thickness: 20mm bonded; 30mm unbonded in homes, 40mm commercial; 35mm floating in homes, 40mm commercial.
  • Over underfloor heating: at least 25mm above the pipes (Cemfloor Therm only; Cemfloor NH is not suitable for heated floors).
  • Bay sizes: up to 150m² unheated and 100m² heated.
  • Foot traffic: 24 to 48 hours.
  • Surface: no laitance, so no sanding, though Cemfloor still recommends lightly preparing the surface to remove site dirt before floor coverings.
  • Wet areas: the data sheet says it can be applied in wet areas.

Cemfloor's underfloor heating guidance says the system can be commissioned after 7 days. The flow temperature starts 5°C above room temperature and rises 5°C a day to a maximum of 40°C, and the heating runs until the screed reaches 2.5% moisture content by the carbide (CM) method.

Because it is cement based, Cemfloor takes cementitious tile adhesives, including fast track systems, and suits a liquid screed in a room that may see water.

Gyvlon: anhydrite (calcium sulphate) flowing screed

Gyvlon is the calcium sulphate flowing screed range of Anhydritec, based in Warrington. Its published figures for the standard ECO screed:

  • Depths: 25mm fully bonded, 30mm unbonded, 35mm floating in homes and 40mm commercial. Thinner products exist: Gyvlon quotes 8mm bonded, 15mm unbonded and 30mm floating for some variants, each with its own conditions.
  • Over underfloor heating: 25mm cover for ECO; 20mm with Gyvlon's Thermio+ technology; Thermio MAX FD E2C is designed for a nominal 15mm above the pipes.
  • Drying: about 1mm a day up to 40mm, then about 0.5mm a day beyond 40mm, in good conditions (20°C, 65% RH).
  • Foot traffic: 24 to 48 hours.
  • Heating: underfloor heating can be commissioned from 7 days. Gyvlon's sequence starts at about 20°C for 24 hours, rises 5°C a day to a maximum of 45°C, holds for 5 days, then comes back down 5°C a day.
  • Surface: standard Gyvlon screeds (ECO, XTR, Thermio and Finio) should be sanded 3 to 10 days after the pour. The "FD E2C" versions do not form loose laitance and do not need that early sanding, and Gyvlon says they dry twice as fast as its standard screeds.

Gyvlon also publishes moisture limits for floor coverings. For tiles fixed with a primer and calcium sulphate tile adhesive, the standard range must be down to 1.0% moisture content, or 1.5% for the E2C range. For vinyl bonded without a levelling compound the limit is 0.5% (1.0% for E2C). Gyvlon's rough conversion puts 0.5% moisture content at about 75% RH.

Alpha flow screed: what it is

"Alpha flow" usually refers to a flowing screed based on alpha hemihydrate, which is also a calcium sulphate binder but is made differently from anhydrite. These products are often picked when depth is tight or the programme is short. They behave like other calcium sulphate screeds (CA designation, laitance, compatible primers and adhesives), but drying, depth and heating rules vary from one product to the next. We could not find one manufacturer's data sheet that covers every product sold under this name, so ask for the exact product name and its data sheet before you plan anything around it.

Our anhydrite screed guide explains calcium sulphate screed in general. This page is about the brand names.

Polymer modified sand and cement (Isocrete K)

Isocrete K-Screed is part of the Isocrete range sold by Flowcrete, now Tremco CPG UK. It is not a liquid screed. It is a semi-dry sand and cement screed, laid and compacted by hand, with a proprietary "K" additive mixed in with the cement, sand and water. The data sheet describes the result as an early drying, high strength screed. You will often see it called a polymer modified screed, but Flowcrete's own data sheet just calls it a proprietary additive.

From the Isocrete K-Screed data sheet:

  • Strength: above 25 N/mm² for Standard K-Screed, above 30 N/mm² for Heavy Duty, and BRE screed test Category A.
  • Minimum thickness: 20mm bonded (Standard, with Polymer 70 primer and grout) or 15mm with M-Bond epoxy; 40mm unbonded; floating "generally 75mm (65mm domestic)".
  • Foot traffic: 24 hours at 20°C, 48 hours at 10°C; full traffic after 7 days.
  • Curing: under polythene for 7 days.
  • Drying: about one week per 25mm in good conditions (20°C, 50% RH), counted from when the curing polythene comes off.

Those floating depths match a normal sand and cement screed. The gain is drying time, provided the additive is dosed and the screed cured as the data sheet says.

Isocrete Flowing K

Do not confuse K-Screed with Isocrete Flowing K, a pumped, cement based liquid screed. Tremco CPG relaunched it in April 2026 in partnership with Cemfloor, and its data sheet lists Cemfloor binder among the ingredients. Minimum depths are 20mm bonded, 30mm unbonded and 40mm floating. Bays can be up to 150m², and there is no laitance to sand off. The standard version is not for heated floors: Tremco CPG makes a separate UFH version.

Where F. Ball fits

The F. Ball products that turn up in flooring specifications are its Stopgap smoothing compounds, which flooring fitters lay on top of a dry screed. Stopgap Green Bag is a two part compound laid 3 to 20mm thick, Stopgap Red Bag is laid 3 to 10mm (fillable to 15mm), and Stopgap Fast-Track 30 is laid 2 to 10mm. If a specification names an F. Ball product, it is describing the levelling layer that goes over the screed, not the screed itself.

Comparison table: depth, drying, tiling, heating

Product (maker)Binder and how it is laidMinimum floating depth (home / commercial)Cover over UFH pipesFoot trafficHeating can startLaitance sanding
Cemfloor Therm (Cemfloor)Cement, pumped liquid35mm / 40mm25mm24 to 48 hoursAfter 7 daysNot needed
Cemfloor NH (Cemfloor)Cement, pumped liquid35mm / 40mmNot for heated floors24 to 48 hoursNot applicableNot needed
Gyvlon ECO (Anhydritec)Calcium sulphate, pumped liquid35mm / 40mm25mm24 to 48 hoursFrom 7 daysSand at 3 to 10 days
Gyvlon Thermio MAX FD E2C (Anhydritec)Calcium sulphate, pumped liquidPer product sheetNominal 15mm24 to 48 hoursFrom 7 daysNo early sanding
Isocrete Flowing K (Tremco CPG)Cement, pumped liquid40mmSeparate UFH version24 to 48 hoursUFH version onlyNot needed
Isocrete K-Screed (Tremco CPG)Sand and cement with additive, hand laid65mm / 75mmSee UFH data sheet24 hours at 20°CSee UFH data sheetNot applicable
Stopgap compounds (F. Ball)Smoothing compound over a dry base2 to 20mm, by productNot a screed30 minutes to 3 hours, by productNot applicableNot applicable

Swipe the table sideways to see every column.

These are minimums from the data sheets. The real depth on your floor also depends on the insulation, the loads and how flat the base is. For a plain comparison of the two main types, see liquid screed vs sand and cement screed.

Tiling onto each type

  • Cement based (Cemfloor, Flowing K, K-Screed): standard cementitious adhesives, once the screed has dried to the limit for the finish.
  • Calcium sulphate (Gyvlon, alpha hemihydrate): remove the laitance, use the primer the adhesive maker specifies, and keep to the lower moisture limits. For heated floors, Gyvlon says the underfloor heating must be commissioned and the run recorded before tiles go down.

Laying a specified product: what to check on the spec

When the drawings name a brand, check these points before you order or book a pour:

  1. The exact product, not just the brand. Cemfloor Therm and Cemfloor NH have different heating rules. Gyvlon ECO and Thermio MAX FD E2C have different cover depths. Ask for the full product name.
  2. The designation. CA or CT, plus the C and F strength classes, for example CA-C25-F5. This tells you the binder and the strength the product has to reach.
  3. Depth against build-up. Compare the specified depth with the product's minimum for the actual build: bonded, unbonded, floating or heated. A 35mm floating screed over pipes may not leave the 25mm cover most standard products need.
  4. Installer requirements. Some manufacturers ask for an approved or licensed contractor. Cemfloor's data sheets say an approved contractor should place it, and the Flowing K data sheet asks for a Tremco CPG licensed contractor, while the K-Screed data sheet says any competent contractor can lay it. If your specification depends on that, tell us when you ask for a price and we will tell you plainly whether we can meet it.
  5. Heating schedule. Get the manufacturer's commissioning sequence to your heating engineer early. Cemfloor caps flow temperature at 40°C during commissioning; Gyvlon goes up to 45°C.
  6. Floor finish and moisture limit. Tell the flooring fitter which screed is going down so they can choose a primer and adhesive and plan moisture testing.
  7. Equivalents. Agree any substitute product with the designer in writing before the pour.

What it costs

Screed manufacturers do not publish installed prices. As a guide, MyJobQuote (updated August 2026) puts liquid screed at £24 to £31 per m² supplied and laid, and sand and cement screed at £18 to £25 per m². The product, depth, area, pump access and any insulation you need all move the price. Our floor screeding cost guide explains how those factors add up.

Get a fixed price for your floor

Send us the specification or the product name, the floor area in m², the depth, the build-up (insulation, underfloor heating or bonded to concrete), what floor finish goes on top, and the site postcode. We will check that the product suits your build-up, confirm whether we can lay it, and give you a written fixed price within 24 hours, agreed before any work starts.

We lay calcium sulphate flow screed and cement based liquid screed across London and the Home Counties from our base in Slough. Send your details through our contact page or call 07466 650936 for a same day call back.

Sources

FAQs

Frequently asked questions

Is Cemfloor better than anhydrite screed?

Neither is better for every floor. Cemfloor suits rooms that may see water, avoids laitance sanding and takes ordinary cement based tile adhesives. Calcium sulphate screeds like Gyvlon offer thin sections over heating pipes, and Gyvlon publishes its own drying and commissioning schedules. The choice usually comes down to the finish, the room's use and how much build height you have.

Can I swap a specified Gyvlon screed for Cemfloor?

Only with the designer's written agreement. Changing from calcium sulphate to cement changes the bay sizes, tiling system, laitance treatment and heating commissioning schedule, and may affect warranties and any thermal performance the heating design relies on. If a swap is suggested, ask for the reason and get the revised specification before the pour date is fixed.

Does a branded screed need a branded primer and adhesive?

Not always the same brand, but it must be a compatible system. Gyvlon recommends an epoxy or acrylic primer under adhesives so the screed does not draw them in too fast. For cement based screeds, standard cementitious adhesives work once the moisture limit is met. Always check the adhesive maker's guidance for the screed type.

Why does my specification say CT-C25-F5?

That is the BS EN 13813 designation. CT means a cement based screed, C25 means a compressive strength of 25 N/mm² and F5 a flexural strength of 5 N/mm². A calcium sulphate screed would start CA instead. Cemfloor lists classes from C20 to C30 and F4 to F6, so a CT-C25-F5 specification sits within its range.

Our services

Services mentioned in this article

Wide view of a finished screed in a glazed extension

Anhydrite Screed

We supply, pump and finish calcium sulphate flow screed to the grade your specification calls for, from CA-C20-F4 to alpha hemihydrate products, over insulation, underfloor heating or concrete.

Smooth self levelled liquid screed across an open plan room

Liquid Screed

Pumped straight from the mixer and self-levelling, liquid screed gives a flat, dense floor that is ideal over underfloor heating and covers large areas in a day.

Power floating a floor screed to a smooth finish

Sand & Cement Screed

The proven, versatile choice. Traditional sand and cement screed is mixed on site, compacted by hand and finished to a level, durable base for any floor covering.

Free, no-obligation quote

Ready to get your floors done properly?

Leave a request and we will call you back the same day. Your quotation will be ready within 24 hours, with no hidden fees and no obligation.